Avaya J129 Installing And Administering Download Page 47

Page: 47 / 133

Chapter 5: Avaya Aura configuration for

phones

SIP phone administration on Communication Manager

The SIP-based calling features in the following table can be invoked directly on Avaya J129 IP

Phone or using a feature button provisioned using Avaya Aura

Communication Manager.

Communication Manager automatically processes other calling features such as call coverage, trunk

selection using Automatic Alternate Routing (AAR), or Automatic Route Selection (ARS), Class Of

Service/Class Of Restriction (COS/COR), and voice messaging.

Note:

• For more information, see

Avaya Aura

Communication Manager Feature Description and

Implementation

and other Communication Manager administration documents at the Avaya

Support website:

http://support.avaya.com/

• For information about IP Office, see

Avaya IP Office

™

Platform SIP Telephone Installation

Notes

The Avaya SIP solution configures all SIP phones in Communication Manager as off-PBX station

(OPS).

Feature

Survivable operation with third-
party proxy

Normal operation with
Communication Manager and
Session Manager

3-Way Conferencing

Yes

Conference using conference
server

—

Yes

Automatic Call Back/Cancel

—

Yes

Call Forward All Calls – on/off

Yes

Call Hold

Yes

Call Park and Unpark

—

Yes

Calling Party Number Block

—

Yes

EC500

—

Yes

Malicious Call Trace

—

Yes

Message Waiting Indication

MWI is not available. If the
PSTN_VM_NUM parameter is

Yes

Table continues…

September 2017

Installing and Administering Avaya J129 IP Phone

Comments on this document? [email protected]

Summary of Contents for J129






































































































































Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands

Avaya J129, Installing And Administering

Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands