Avaya J129 Installing And Administering Download

Page: 70 / 133

Device upgrade process

1. During boot-up, the phone receives the file server address from DHCP, LLDP, or the device

interface.

2. The phone contacts the provisioning server to download the firmware upgrade file,

J100Supgrade.txt

3. In

J100Supgrade.txt

, the APPNAME parameter contains the firmware version.

4. The phone compares the currently installed software version with the version specified in the

APPNAME parameter.

5. If the firmware version specified in the APPNAME parameter is higher, the phone downloads

the software files for upgrade.

6. The phone automatically restarts to apply the upgraded firmware.

Tip:

The upgrade events are logged under NOTICES level in the

Syslog

file.

User profile backup on Personal Profile Manager (PPM)

Phone supports data backup by saving all non-volatile user parameters on PPM . When the user
logs in to any registered device, PPM restores all user data on the device.

Note:

PPM is only available in an Avaya Aura

environment.

User profile parameters for backup

The following table lists the parameters that are backed up on Personal Profile Manager (PPM).

Parameter

Default
value

Description

CLICKS

Specifies if the phone button can generate click sounds.

OUTSIDE_CALL_RING_TYPE 1

Specifies the default outside call ring type.

CALL_PICKUP_INDICATION

Specifies the following call pickup indication types:

• Audio

• Visual

• None

Table continues…

Maintenance

September 2017

Installing and Administering Avaya J129 IP Phone

Comments on this document? [email protected]

Summary of Contents for J129






































































































































Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands

Avaya J129, Installing And Administering

Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands