Avaya J129 Installing And Administering Download Page 115

Page: 115 / 133

Parameter name

Default value

Description

• 6: 1Gbps full-duplex, if supported by hardware,

otherwise auto-negotiated

PHY2_AUTOMDIX_ENABLED

Specifies whether auto-MDIX is enabled on PHY2.

Value Operation:

• 0: auto-MDIX is disabled.

• 1: auto-MDIX is enabled.

PHY2PRIO

Specifies the layer 2 priority value to be used for
frames received on the secondary Ethernet
interface when VLAN separation is enabled. The
parameter is not supported when VLANSEPMODE
is 1.

Valid values are 0 through 7.

PHY2STAT

Specifies the speed and duplex settings for the
secondary (PC) Ethernet interface.

Value Operation:

• 0: disabled

• 1: auto-negotiate

• 2: 10Mbps half-duplex

• 3: 10Mbps full-duplex

• 4: 100Mbps half-duplex

• 5: 100Mbps full-duplex

• 6: 1Gbps full-duplex, if supported by hardware,

otherwise auto-negotiated

PHY2TAGS

Determines whether or not VLAN tags are stripped
on Ethernet frames going out of the Computer (PC)
port.

Value Operation:

• 0: Strip tags. VLAN tags are stripped from

Ethernet frames leaving the computer (PC) port
of the phone.

• 1: Does not strip tags. VLAN tags are not

stripped from Ethernet frames leaving the
Computer (PC) port of the phone.

Note:

This parameter is configured through the
settings file.

Table continues…

September 2017

Installing and Administering Avaya J129 IP Phone

115

Comments on this document? [email protected]

Summary of Contents for J129






































































































































Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands

Avaya J129, Installing And Administering

Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands