Avaya J129 Installing And Administering Download

Page: 61 / 133

Configuration Parameter Name

Description

VLAN ID

Specifies the ID for VLAN. The available format is

dddd

VLAN Test

Specifies the time in seconds, the phone waits for
the DHCP server response. The available format is

ddd

The following parameters are available in Servers menu:

HTTP server

Specifies the IP address of the HTTP file server. The
available format is

nnn.nnn.nnn.nnn.

HTTPS server

Specifies the IP address of the HTTPS file server.
The available format is

nnn.nnn.nnn.nnn.

DNS server

Specifies the IP address of the DNS server. The
available format is

nnn.nnn.nnn.nnn.

SNTP server

Specifies the time server settings.

Using the debug mode

About this task

Use this procedure to activate or deactivate the debugging options.

Before you begin

You must set a HTTP server in the BRURI parameter in the

Settings

file that is capable of

receiving a phone report from the phone.

Procedure

1. Press

Main Menu

Admin

2. In the

Access code

field, enter the admin menu password.

3. Press

Enter

4. Select

Debug

The phone displays the following debug options:

•

Phone Report

•

Port Mirroring

•

SSH

•

SSH fingerprint

•

Svc control

•

Svc record

Using the debug mode

September 2017

Installing and Administering Avaya J129 IP Phone

Comments on this document? [email protected]

Summary of Contents for J129






































































































































Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands

Avaya J129, Installing And Administering

Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands