manualshive.com logo in svg

AutoGate Shield M30 Series, Installation & Operation Manual

Share
Download
AutoGate Shield M30 Series Installation & Operation Manual Download Page 9

1.800.944.4283             AutoGate Technical Support

 

                          

Mar 6, 2019 

 9 

 

 

he 

to 

low-

er) the Drop arm/gate.

 

 

he 

member of the operator the Drop arm/gate is 

bolted to and lifts  the Drop arm/

 

 

the 

attach to and by adjusting up and or down 

or subtracts tension to 

the 

of 

of the Drop arm/

.

 

 

the public 

of 

the 

protection from the 

.

 

 

 

to 

the 

 

there  no Drop arm/

 

 A

installation 

work. 

 

 

HP  Motor 

  The 

motor shaft and output drive shaft are oriented at 90° 
from each other. This type of drive 

for smoother 

the 

 movement 

not 

drivable.

 

 

to 

the 

 

from the belt 

or 

of the Drop arm/

 

(Limit/Position 

 

An electronic position sensor mounted on the main pulley 
drive shaft that provides Drop arm/gate position feedback to 
the control board.  This component 

two 

a  fea-

tures:

 

 entrapment protection 

obstructions that 

block

 

stop the 

 travel.

 

“open” 

limit positions

 

SECTION 2 — TERMS

 

Summary of Contents for Shield M30 Series





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands