manualshive.com logo in svg

AutoGate Shield M30 Series, Installation & Operation Manual

Share
Download
AutoGate Shield M30 Series Installation & Operation Manual Download Page 24

1.800.944.4283             AutoGate Technical Support

 

                          

Mar 6, 2019 

 24 

Placing the Operator & Drop arm/gate assembly on the Concrete Pad  

 

Be sure the linkage arm attached to the Drop arm/gate is fully straight and in the locked (or over center) posi-
tion.    Press  down  on  the  linkage  arm  to  ensure  it  is  in  its  locked  position.   

DO  NOT  REMOVE  THE  T/M 

SAFETY PIN UNTIL INSTRUCTED TO!

 

Open the operator doors with the supplied keys.  The keys to the doors are attached to the T/M Safety Pin 
keeper (see photo to the left).   

 

 

 

 

 

 

 

 

 

 

 

 

Using a Fork Lift to move and place the operator  

 

 

1.  Remove the T/M Safety Pin (position #1) it may be necessary to push down on the end of Drop arm/gate 

to  take  pressure  off  T/M  Safety  pin)  and  insert  it  in  the  second  set  of  T/M  (position  #2)  bracket  holes.  

Note: 

the photo below shows the pin in position #2 possible if the Drop arm/gate is completely lowered.  

The second set of T/M bracket holes (position #2) is primarily used for installation to allow the Drop arm/
gate to be raised slightly; however, it can also be used to lock the gate in the fully open position. 

 

2. 

Once the operator doors are open pull the Manual Release Lever located by the motor. 

 

 

T/M PIN POSITION #2 and #1 

PREPERATION, ATTACHING THE DROP ARM, & OPERATOR INSTALATION 

KEYS 

MANUAL RELEASE LEVER 

FORKLIFT GUIDES 

FORKS GO HERE 

Summary of Contents for Shield M30 Series





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands