manualshive.com logo in svg

AutoGate Shield M30 Series, Installation & Operation Manual

Share
Download
AutoGate Shield M30 Series Installation & Operation Manual Download Page 30

1.800.944.4283             AutoGate Technical Support

 

                          

Mar 6, 2019 

 30 

 

Typical 24V series connection 

1)  Jumper wire from battery 

1  NEGATIVE is connected 
to battery 2 POSITIVE.  

2)  Wire from battery 1 POSI-

TIVE to POSITIVE terminal 
on control board 

3)  Wire from battery 2 NEGA-

TIVE to NEGATIVE terminal 
on control board. 

Batteries will charge when AC power or Solar Panels are present and power gate automatically without any changes in 
wiring. Note: Solar applications will require a program selection in the board menu (see page 

??

. 

The Genesis controller has a built-in battery charging system that has multiple formats.  The charging sequence can 
handle full size flooded batteries as well as sealed lead acid or AGM batteries.  The Genesis primary input voltage can 
also be connected directly to solar panel(s) for non-AC operation.  The built-in charger when programmed for solar will 
allow the system to run off the batteries and will still charge them during the daylight hours. 

 

Install Two (2) 12 VDC Batteries (Required, not provided) on the battery shelf. AutoGate recommends Group 24 Deep 
Cycle Marine Starting batteries for extended battery back up.  At a  minimum use (2) 7AH batteries for battery back up.    

 

 

Install an approved 8’ earth ground rod 6” to 3’ off the rear side of operator pad*. The Ground wire connection is 
located inside the door. Recommended wire is #8 gauge or larger.  NEVER splice the ground wire! 
 
Improper  grounding  will  make  the  operator  more  susceptible  to  lightening  or  surge  damage  and  can  affect       
GENESIS Board or accessories.  

1 

2 

*Check national and local 
codes for proper depth.  

To Operator 

Summary of Contents for Shield M30 Series





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands