manualshive.com logo in svg

AutoGate Shield M30 Series, Installation & Operation Manual

Share
Download
AutoGate Shield M30 Series Installation & Operation Manual Download Page 31

1.800.944.4283             AutoGate Technical Support

 

                          

Mar 6, 2019 

 31 

The AutoGate Genesis control board is DC powered as is the motor with built in full battery back-up.  Primary power is 
supplied by an AC/DC rectified output power supply (see below).  Input AC is supplied through a dedicated 20  Amp 
breaker.  Voltage is selectable, 90~132 VAC / 180~264 VAC via slide switch.  This protects the Genesis controller from 
random or storm induced power surges on while AC power.  The Earth Ground connection on the board is to aid in 
surge protection and random voltage issues. 

NOTE: There is NO AC power inside the Control Board Enclosure! 

 

 

Run AC power lines through conduit to junction box (see below) located inside the operator. (see typical conduit 
locations drawings page 14. Contact AutoGate for Optional routing). 

 

All AC power and control wiring MUST be run in separate conduits 

 

Before doing any wiring inside the operator ensure that the main power source has been disabled at the main cir-
cuit breaker.  If this is a SOLAR application, ensure the power input is disconnected. 

 

The Power Supply will be wired a the factory, you only need to hook the AC into the supplied junction box. 

WARNING:  ALL 120VAC OR 240VAC ELECTRICAL CONNECTIONS FROM SERVICE 
PANEL TO THE GATE OPERATOR MUST BE MADE BY A LICENSED ELECTRICIAN! 

 

Rectified Power Supply 

(Mounted under the 

battery shelf) 

P11 

AC Junction Box 

Summary of Contents for Shield M30 Series





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands