manualshive.com logo in svg

AutoGate Shield M30 Series, Installation & Operation Manual

Share
Download
AutoGate Shield M30 Series Installation & Operation Manual Download Page 25

1.800.944.4283             AutoGate Technical Support

 

                          

Mar 6, 2019 

 25 

Close the operator doors and latch them in the closed position so they do not swing open while moving, lifting 
or adjusting the operator.  Using a forklift, with side-shift if possible, insert the forks into the channel receivers 
on the door side of the operator. 

 

 

  

 

 

 

 

 

 

Lift the Linkage Arm at the 

center point 4-6 inches to re-

lease the Drop arm/gate 

(shown below). 

 

 

 

 

 

 

Push the gate open until it rests against the T/M Safety Pin now positioned in the second set of T/M bracket 
holes (position #2). 

From  the  public  side,  position  the  operator  in  front  of  the  raised  concrete  pad.    Carefully  raise  the  system 
enough to clear the Bolsters.  Slowly advance and lower once the Drop arm/gate is centered between the op-
erator end Bolster as shown below.  Once lowered, side shift the system to position the operator end barrier 
arm pin to be 50% “engaged in the pin cup.  Fully lower the system leaving the forklift in place.  By design, the 
YOKE END pin will NOT be 50% in the pin cups. 

 

 

PREPERATION, ATTACHING THE DROP ARM, & OPERATOR INSTALATION 

Summary of Contents for Shield M30 Series





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands