manualshive.com logo in svg

AutoGate Shield M30 Series, Installation & Operation Manual

Share
Download
AutoGate Shield M30 Series Installation & Operation Manual Download Page 36

1.800.944.4283             AutoGate Technical Support

 

                          

Mar 6, 2019 

 36 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Type B2 (contact) 

Contact Edge S

ensors 

Close or Closing 

Contact edges on the bottom of the gate are often added 
as  an  extra  entrapment  device  for  the  closing  mode.  We 
do not recommend a contact edge to be the only external 
entrapment device for the closing mode.  

 

Open Edge 

 

Close Edge 

 

Programmable Inputs  (x2) 

 

Approved  Edge Sensor Devices:

 Miller Edge CPT 223, ASO SENTIR 15-10VT, 45 STKS4 

 

 

Open or Opening 

Your Vertical Pivot operator now requires a minimum of (1) OPEN obstruc-
tion device to be wired to the Genesis Control board to operate. You may 
use  any  approved  device  listed  above.    The  face  and  the  throat  area  are 
required to be protected per UL325 7th edition. 

NOTE: 

The two programmable inputs can be configured as either edge or beam and as either open or close.

 

 

MONITORED DEVICE CONNECTIONS POINTS 

P4 & P5

 

Summary of Contents for Shield M30 Series





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands