manualshive.com logo in svg

AutoGate Shield M30 Series, Installation & Operation Manual

Share
Download
AutoGate Shield M30 Series Installation & Operation Manual Download Page 40

1.800.944.4283             AutoGate Technical Support

 

                          

Mar 6, 2019 

 40 

 

Primary/Secondary communications allow for communications between gates for Dual Gate configurations. 

(Not used on SHIELD 

CRASH systems. Information purposes only) 

When using two gates to cover a driveway and they both need to cycle 
together on an open input. Connect the two boards with a 4-conductor 
SHIELDED 18 ga. wire (3 required, 1-spare) and set the following board 
parameters:  

 
P/M: Set for Primary /Secondary communica-
tion.  Gates need to communicate with each 
other to work properly. 
 

 

Your gate is equipped with a LIMIT/POSITION SENOSR.  It will be properly set when 
it leaves the factory.  If you need to adjust it, refer to the instructions below.  If you 
need to replace, contact AutoGate. 

ADJUSTING THE LIMIT/POSITION SENSOR 

 

 

 

1.  In programming mode, Set your cursor to the GATE (line 2) and enter (>Gate).  

Using the Jog knob you can slightly adjust the OPEN or CLOSE position by turn-
ing it left or right.  

2.  Once you have readjusted your gate position, “enter” again to back out of the 

Gate line and go up to the Op: line or down to the Cl: line to set your new num-
bers.  

>Dual Gate Mode: 
  Off 

P8 

P10 

>Op:4500 Ramp:4000 
 Gate 1 

WARNING! This screen requires a PASSCODE to access. 

Summary of Contents for Shield M30 Series





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands