manualshive.com logo in svg

AutoGate Shield M30 Series, Installation & Operation Manual

Share
Download
AutoGate Shield M30 Series Installation & Operation Manual Download Page 13

1.800.944.4283             AutoGate Technical Support

 

                          

Mar 6, 2019 

 13 

SITE PREPARATION & PLANNING 
 

When you ordered your system you specified either a right-hand or left-hand system.  See Pages 12-18 for 
examples  of  a  LEFTHAND  and  RIGHTHAND  pad  and  operator  layouts.    From  these  illustrations  and  your 
specific  site  layout,  you  must  decide  exactly  where  operator  and crash  barrier  Bolsters  will  be  finally  posi-
tioned.    You  also need to determine  the trenching  and running  of conduit  around the  access  control  point, 
back to the operator for power and control connectivity.   

Determine if there are any accessory components to be installed with your system such as traffic lights, in-
ground loops, access control stations, etc. and factor them into your site layout and installation plan. Inspect 
the  site  and  verify  there  are  no  underground  utilities,  overhead  wires,  or  other  obstructions  that  can  effect 
your installation and use.  If possible, keep routine foot traffic away from the system to reduce the chance of 
pedestrian or site personnel coming in contact with a moving barrier system. A separate pedestrian gate or 
turnstile  is  highly  recommended  so  as  to  discourage  the  use  of  the  barrier  system  by  anything  other  than   
vehicular  traffic.    This  evaluation  and  planning,  along  with  coordination  with  electricians  and  other  on-site 

SITE PLANNING

 

Access Control  
      Station 

Optional Electrical & 

Access Control     

Enclosure 

AC Primary Power 

Photo Eye Beam 

Note: Photo Eye Requires power at Yoke End 

Summary of Contents for Shield M30 Series





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands