manualshive.com logo in svg

AutoGate Shield M30 Series, Installation & Operation Manual

Share
Download
AutoGate Shield M30 Series Installation & Operation Manual Download Page 29

1.800.944.4283             AutoGate Technical Support

 

                          

Mar 6, 2019 

 29 

Warning Signs 

AutoGate recommends any additional signage be installed between the operator and the center of the Drop 
arm/gate.  

DO  NOT  DRILL  OR  PIERCE  THE  DROP  ARM/GATE.   

This will allow undesired water, ice, and 

condensation to enter the Drop arm/gate and void your warranty.  Alternate fastening method is required (ex: 
ultra high bond  exterior tape) to avoid violating the warranty. 

      

 

EXAMPLE SIGN LOCATIONS

                               

 

 

Reflective Tape & Warning Lights 

Several organization's and standards now specify that Active Barrier Systems and non-crash barrier systems 
are to be  conspicuously  marked  and  or  have warning  lights for the  system.  Some  of the  organizations and 
standards are, but not limited to: Surface Deployment and Distribution Command Transportation Engineering 
Agency (SDDCTEA), Manual of Uniform Traffic Control Devices (MUTCD), Unified Facilities  Criteria (UFC), 
Department of Transportation (DOT), Federal Highway Administration (FHA), etc.  Below you will see an  ex-
ample of a Drop arm/gate system with a gate panel fabricated to the Arm (optional), High Intensity  Prismatic 
Reflective Tape, and LED lights mounted to and fully protected by rigid conduit. 

 

 

 

 

 

DO NOT affix any adhesive material within 30 days of receiving the system. 

 

The gate and operator are designed to work together. DO NOT attempt to install or affix an unauthorized 
gate without AutoGate’s prior authorization and instructions, doing so may VOID the operator warranty.  

 

DO NOT ALLOW any access control devices to be mounted within 6 feet of the moving gate or in such a 
way that someone could reach their hand or arm through the gate to activate it. 

Summary of Contents for Shield M30 Series





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands