manualshive.com logo in svg

AutoGate Shield M30 Series, Installation & Operation Manual

Share
Download
AutoGate Shield M30 Series Installation & Operation Manual Download Page 27

1.800.944.4283             AutoGate Technical Support

 

                          

Mar 6, 2019 

 27 

Gate Guard 

Supplementary Tasks Following Final Positioning & Before Initial Operation   

Before beginning routine operation of your barrier system, you must complete several other tasks to ensure 
the gate is ready for service and is operating correctly. 

Remove the T/M Safety Pin and properly stow on the stowage hook inside the  operator. 

 

 

 

 

 

 

 

 

Attach the kick panel to the door side of the operator using #12 x 3/4” TEK (self-drilling screws provided). 
The kick panel blocks any reaching under and into the operator to prevent injury during operation.  It also 
blocks debris and vamints from getting underneath.  

 

 

 

 

 

Attach The Gate Guard 

If shipped unattached, mount the gate guard to the back of the operator cabinet to cover the opening at the 
end opposite the Drop arm/gate using #12 x 2.0” TEK (self-drilling screws provided). 

 

PREPERATION, ATTACHING THE DROP ARM, & OPERATOR INSTALATION 

T/M SAFETY PIN STORED 

 

FASTEN KICK 
PANEL HERE 

KICK PANEL 

Summary of Contents for Shield M30 Series





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands