AutoGate Shield M30 Series Installation & Operation Manual Download Page 8

Page: 8 / 60

1.800.944.4283 AutoGate Technical Support

Mar 6, 2019

OPERATOR FRAME

Main operator frame, 2” sq. steel tube construction

THROAT

Area between the operator and false panel where the gate opens up

TRANSPORT/MAINTENANCE PIN (T/M)

Used for locking the arm in place with or without the gate attached

OPERATOR ARM

Main 2” x 4” steel tube where the gate attaches

STAINLESS STEEL FOOTPADS

No messy rusty footpads

KICK PANEL

Prevents access under the operator and debris out

24VDC 90° RIGHT ANGLE DRIVE MOTOR (RAD)

1/2hp Gear motor drive to ensure safe and smooth operation

MANUAL OPERATION REALEASE LEVER

Disengages the coupler and allows the gate to be raised by hand

MOTOR DRIVE BELTS

(3) High quality “A” Section cogged belts...

MOTOR DRIVE BELT TENSIONER

One shown, total of two

GATE BELT TENSIONER (Not shown, behind #12)

Allows you to tighten the belts (Not shown behind the Drive Pulley)

INTERMEADITE DRIVE PULLIES

Provides high torque to move the gate

GATE DRIVE BELTS

(2) High quality V-belts to move the gate

MAIN GATE DRIVE PULLEY

Provides high torque to move the gate

LIMIT/POSITION SENSOR (LPS) (behind #28)

Digital Sensor that sets the open and close locations of the gate

SLIDE ASSEMBLY

Adjust the balancing up or down on the threaded rod (not pictured)*

T-BOLT ASSEMBLY

Fine tuning of the balancing

CHAIN TENSIONING BOLT ASSEMBLY

Roller chain attaches here

#80 ROLLER CHAIN

Connects the springs to the Chain tension Bolt

SPRINGS (Qty. will vary on gate size and weight)

Depending on gate size & weight, you can have 2 to 8 springs

REAR SPRING BARS

Attaches the springs, Qty. will vary on the # of springs

BATTERIES ((2) required, not supplied)

Min. 7Ah batteries, recommend Group 24 100Amp Marine Starting

BATTERY TRAY/POWER SUPPLY (Under Battery tray)

Main Power Supply is mounted under the Battery Tray

3Amp AC Fuse

AC Supply fuse

AC/DC MAIN ON/OFF SWITCH

Turns on both the AC and DC power in one switch

INCOMING AC VOLTAGE JUNCTION BOX

Normally 120Vac, 240Vac compatible

FAULT LIGHT

Three flash modes: 1. Fault, 2: DC Power issue, 3: AC power issue

CONTROL BOX

Houses the Genesis control board and other accessory items

GENESIS CONTROL BOARD

State of the art control board with 4-line digital display

UL325 SIREN

Will be activate upon an UL fault

* See Balancing Instructions for Slide details

OPERATOR DETAILS

Summary of Contents for Shield M30 Series





























































Search results

Summary of Contents for Shield M30 Series

Reviews:

Brands by name

Popular brands

AutoGate Shield M30 Series, Installation & Operation Manual

Search results

Summary of Contents for Shield M30 Series

Reviews:

Brands by name

Popular brands