manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 490

Removing the radiator

•

Remove both fairing lugs

•

Remove the right duct bulkhead

•

Remove the screw (1) fixing the oil ra-

diator to the securing bracket

•

For an easier removal of the radiator

lock lower pin, remove the screw (2) on

the engine head that secures the radi-

ator clamp.

•

Remove the Seeger locking (3) of the

right side lower radiator pin

•

Extract the left side pin (4) of the mo-

torcycle

Cooling system

Caponord 1200 - Caponord 1200 Rally

COOL SYS - 490

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands