APRILIA Caponord 1200 2016 Manual Download Page 462

Page: 462 / 573

Characteristic

Value/example

Unit of

measure

ment

Notes

Battery voltage

11.9

ACTIVATION screen page

On this screen, you can delete the errors from the

memory of the controller and you can enable some

systems controlled by the control unit.

ACTIVATION

Characteristic

Value/example

Unit of

measure

ment

Notes

Front brake bleeding procedure

Useful in case of lever sponginess although the

bleeding has been done as in a regular braking

system

Rear brake bleeding procedure

Useful in case of lever sponginess although the

bleeding has been done as in a regular braking

system

ABS warning light

The ABS warning light is made to flash.

Ambient parameter error reading (1)

The ambient parameters are 4: Number of error

detections, Operation cycles from the last detec-

tion, Battery voltage, Speed.

Ambient parameter error reading (2)

Number of error detections: number of times the

error has been detected by the control unit;

Ambient parameter error reading (3)

for example, if it indicates 2, it means that the error
has been detected (ATT), then it has not been de-

tected for a while (sent to the MEM) and then it

has been detected again.

Ambient parameter error reading (4)

Operation cycles from the last reading: a cycle is

counted if the following occurs: key ON and speed

over 20 km/h.

Ambient parameter error reading (5)

If for example 5 is shown, it means that the last

time the error has been measured was 5 cycles

ago.

Error clearing (1)

Press "enter" to transfer errors from the memory

(MEM) to the historical record (STO).

Error clearing (2)

At the next connection between diagnostics in-

strument and the control unit, the historical errors

(STO) will no longer appear.

Braking system

Caponord 1200 - Caponord 1200 Rally

BRAK SYS - 462

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Caponord 1200 2016

Reviews:

Brands by name

Popular brands

APRILIA Caponord 1200 2016, Manual

Search results

Summary of Contents for Caponord 1200 2016

Reviews:

Brands by name

Popular brands