manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 362

•

Position the gear sensor and screw the

two fixing screws.

•

Refit both head-cylinder assemblies.

•

Position the crankshaft gear.

•

Fit the special tool, tightly fastening the

three screws securing the tool onto the

crankcase.

Specific tooling

020850Y

 

Primary gear lock

•

Position the water pump drive gear, the

washer and crankshaft fastener nut

and tighten it to the specified torque.

Engine

Caponord 1200 - Caponord 1200 Rally

ENG - 362

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands