manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 184

check the continuity of the cable that is not functioning properly: if there is continuity, replace

the control unit; if not, restore the wiring

White rear connector throttle grip position sensor - track D P0153

•

short circuit to positive / open circuit, short circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 11 of the ENGINE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 11 of the ENGINE connector

Troubleshooting

•

shorted to positive: check the value shown by the parameter of the white rear connector

Throttle Grip Position Sensor - track D: disconnect the connector and read the value indi-

cated by the diagnostics instrument: if the voltage does not vary, there is a short circuit in

the cable wiring; replace the throttle grip sensor if the voltage drops to zero.

•

if the circuit is open, shorted to negative: check the throttle grip sensor connector and the

Marelli control unit connector. If not OK, restore. If OK, check circuit continuity between the

two cable terminals. If not OK, restore; if OK, check the cable ground insulation (from the

throttle grip sensor connector or the control unit connector): if the cable is not ground insu-

lated, restore the wiring. If it is ground insulated, and with the switch key set to ON, check

that there is power supply for the potentiometer PIN D and that PIN F is connected to ground.

If both are correct, replace the throttle grip sensor; if not, check the continuity of the cable

that is not functioning properly: if there is continuity, replace the control unit; if not, restore

the wiring

DIAGNOSTICS INSTRUMENT: LOGIC ERRORS

Blue front connector throttle grip position (tracks A-B) P0154

•

inconsistent signal

Error cause

•

Two illogical voltage signals have been detected at PIN 13 and 39 of the ENGINE connector

(tracks A-B)

Troubleshooting

•

Check the parameters of the blue front connector Throttle Grip Position Sensor - tracks A

and B: if one of the two values clearly deviates from 600-1400 mV, it means that this po-

tentiometer is defective. Check the throttle grip sensor connector and the control unit

connector: if not OK, restore. If OK, check that cable resistance between the throttle grip

sensor connector and the control unit is a few tenths of Ohm: if this is not the case, restore

wiring. If the value is correct, replace the complete throttle grip sensor

White rear connector throttle grip position (tracks C-D) P0155

Electrical system

Caponord 1200 - Caponord 1200 Rally

ELE SYS - 184

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands