manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 411

•

Insert the first gear, keep the front

brake lever blocked with an elastic,

then lift the rear wheel of the vehicle.

•

Once the rear wheel is lifted, solidly fix

the vehicle on the lift.

•

DO NOT LIFT THE VEHICLE WITH

THE REAR HANDLE.

•

DO NOT USE MOTORCYCLE JACK

STANDS ANCHORED TO THE REAR

SWINGARM.

THE FOLLOWING PROCEDURE APPLIES TO THE ADD VERSION

•

Disconnect the electric motor connec-

tor (1).

•

Release the elastic that keeps the elec-

tric motor in position.

Caponord 1200 - Caponord 1200 Rally

Suspensions

SUSP - 411

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands