manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 356

Thoroughly clean the two sections of the crankcase, the ball bearings, the threads of the crankcase

fixing screws and the bearing seats with a non-aggressive solvent. Clean the seal surfaces and check

that they are not damaged.

CAUTION

TO AVOID DAMAGING BOTH CRANKCASE HALVES PLACE THEM ON A FLAT SURFACE.

Check that both crankcase halves are not cracked or damaged.

Check that all threads are in proper conditions.

Check that all oil seals remaining in their position are not worn or damaged.

Check all ball bearings for clearance, smoothness and potential distortions.

CAUTION

LUBRICATE BALL BEARINGS WITH ENGINE OIL BEFORE FURTHER CHECKING.

If the internal ring does not rotate smoothly and silently or if there is some noise while it turns, it means

that the bearing is faulty and must be replaced.

OIL FILTER AND OIL DELIVERY PIPE CHECK

Check the oil filter for damage. If necessary, replace the part.

Clean the oil net with petrol and inspect the net links for potential damage.

CHECK THE ENGINE OIL FILTER O-RING.

LUBRICATION CHECK

•

Working on both crankcase halves, re-

move and thoroughly clean the nozzle

that lubricates the piston crown.

REPLACE THE SPRAY NOZZLE O-RING IF NECESSARY.

Engine

Caponord 1200 - Caponord 1200 Rally

ENG - 356

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands