APRILIA Caponord 1200 2016 Manual Download Page 337

Page: 337 / 573

pos.

Description

Type

Quantity

Torque

Notes

Camshaft retainer plate fastener

screw

torx M5

8.5 Nm (6.26 lbf ft)

3M SCOTCH GRIP

2353

Decompression device fixing screw

torx M8

28.5 Nm (21.02 lbf ft)

3M SCOTCH GRIP

2353

Fastener screw

5.50 Nm (4.06 lbf ft)

3M SCOTCH GRIP

2353

Installing the chain tensioner

Refit the removed timing system chain tensioner on the cylinder - head:

•

Fit the timing chain on the crankshaft and on the intermediate gear.

•

Remove the screw and collect the washer and the spring.

•

Fit the chain tensioner body on the cyl-

inder and insert a new paper gasket.

•

Tighten the two screws to the prescri-

bed torque.

•

Insert the spring and tighten the screw together with the washer.

Cam timing

Timing

•

Remove the flywheel.

•

Install the timing chains on the inter-

mediate gears.

•

Install special tool flange on flywheel

side crankcase and fasten it using the

two screws supplied.

Specific tooling

020720Y

Timing tool

Caponord 1200 - Caponord 1200 Rally

Engine

ENG - 337

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Caponord 1200 2016

Reviews:

Brands by name

Popular brands

APRILIA Caponord 1200 2016, Manual

Search results

Summary of Contents for Caponord 1200 2016

Reviews:

Brands by name

Popular brands