APRILIA Caponord 1200 2016 Manual Download Page 347

Page: 347 / 573

•

The piston rings are different and must

be installed with the marking at the top.

•

Fit the lower oil scraper ring on the pis-

ton with the gap turned towards the

exhaust side.

•

Install the remaining piston rings on the

piston, offsetting the gaps in the rings

by 120° relative to each other.

•

Fit a new retainer ring on the piston.

•

Insert piston in the cylinder using the

tool.

Specific tooling

020895Y

Piston installation ring

•

Install the second pin retainer ring on

the tool guide, as shown in the figure.

•

Insert tool shaft and push retainer ring

inside the guide until reaching the

height shown in the figure.

•

Fit a new base gasket.

•

Fit the piston-cylinder assembly previ-

ously assembled on the stud bolts,

aligning pin with connecting rod big

end.

•

Fit the tool in the pin and push shaft to

position the retainer ring in its seat.

Specific tooling

020894Y

Pin snap ring fitting tool

Caponord 1200 - Caponord 1200 Rally

Engine

ENG - 347

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Caponord 1200 2016

Reviews:

Brands by name

Popular brands

APRILIA Caponord 1200 2016, Manual

Search results

Summary of Contents for Caponord 1200 2016

Reviews:

Brands by name

Popular brands