manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 464

Characteristic

Value/example

Unit of

measure

ment

Notes

(can be read in the ISO page on the Vehicle code
line) and the value detected by the cabling identi-

fication PINs

(can be read in the ISO page Vehicle identification

line on the basis of the status of Pins 2 and 15)

and, for Caponord 1200, from the CAN signal re-

ceived from the injection control unit

F000 Control unit

Possible control unit fault

SETTINGS screen page

This screen is used to adjust some control unit pa-

rameters.

ADJUSTMENTS

Characteristic

Value/example

Unit of

measure

ment

Notes

Coding (1)

Allows for the coding of a new control unit, or else

the recoding of the existing control unit.

Coding (2)

Vehicle identification is done according to the con-

nection of PINS 2 and 15 of the ABS control unit

connector and is stored in the control unit memory.

Coding (3)

The identification can be read on the INFO ECU

screen on the line: Vehicle code.

NOTE: the "X" in the table identifies the connector pin is grounded.

* - CAPONORD 1200 and all motorcycles equipped with ABS control units connected via CAN

line

Braking system

Caponord 1200 - Caponord 1200 Rally

BRAK SYS - 464

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands