manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 232

•

If the circuit is open, shorted to negative: carry out the check procedure on the component

and the EVC connector. Disconnect the two connectors and check for continuity of the cable

between potentiometer PIN 2 and EVC PIN A5 and restore the cable harness. If the cable

harness is intact check component PIN 2 ground insulation: if insulation is not present, re-

store the cable harness; otherwise replace the component.

(Caponord 1200 Travel Pack)

DIAGNOSTICS INSTRUMENT: LOGIC ERRORS

Exhaust butterfly valve position P0190

•

position error.

Error cause

•

Position indicated by potentiometer does not correspond with position set by control unit.

Troubleshooting

•

Mechanically check the valve, its normal rotation (with cables disconnected from motor,

manually activate the cables and see movement regularity and check valve complete stroke

with correct operation of the return spring) and absence of foreign bodies which do not allow

its rotation: if not OK, restore; if OK, check valve and instrument panel connectors (special

attention to oxidation) and check cables resistance: if not OK, restore; if OK, always with

cables disconnected and key set to ON, check normal rotation of the electric motor and

replace motor (potentiometer does not work correctly).

DIAGNOSTICS INSTRUMENT: ADJUSTABLE PARAMETERS

•

Acquire exhaust butterfly valve zero position.

NOTE: Motor is placed in a reference position to correctly search mechanical stop later.

•

Exhaust butterfly valve self-acquisition

NOTE: Search minimum and maximum mechanical stop.

Exhaust butterfly valve stop search P0191

•

excessive time / search not carried out, incorrect travel / potentiometer signal above MAX

threshold and under MIN threshold

Error cause

•

If search not carried out. Carry out travel stop search.

•

If time is excessive: failure to memorise valve stop positions. The VCU is unable to record

the valve stops: probable circuit interruption. If the search is not carried out, incorrect travel:

memorisation of valve stop positions absent: this occurs at the first start of the bike or fol-

lowing a control unit reset.

•

If incorrect travel, carry out reset, cable adjustment and stop search again.

Troubleshooting

Electrical system

Caponord 1200 - Caponord 1200 Rally

ELE SYS - 232

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands