manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 206

0.7 - 0.9 

Ω

 at ambient temperature

Pin out:

1. Power Vbatt

2. Secondary circuit to ground

3. Activation from control unit

DIAGNOSTICS INSTRUMENT:PARAMETERS

Example value with key ON:

 Current ignition advance.

Example value with engine on:

 Indicates the cylinder advance where combustion will take place.

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

DIAGNOSTICS INSTRUMENT: ACTIVATION

Front Central Coil:

The auxiliary relay (No. 46 in the wiring diagram, placed in the front relay box, left side; CHECK, how-

ever, the identification of the relay with the colour of the cables) is energised for 5 seconds and the coil

Pink cable is closed to ground for 2 ms per second. Disconnect the 4-way connector of the fuel pump

to be able to hear the relay and injector activation. The continuity of the wiring is necessary for correct

activation: no error indications are displayed in case of lack of activation.

Rear Central Coil:

The auxiliary relay (No. 46 in the wiring diagram, placed in the front relay box, left side; CHECK, how-

ever, the identification of the relay with the colour of the cables) is energised for 5 seconds and the coil

Purple/Grey cable is closed to ground for 2 ms per second. Disconnect the 4-way connector of the fuel

pump to be able to hear the relay and injector activation. The continuity of the wiring is necessary for

correct activation: no error indications are displayed in case of lack of activation.

Front Side Coil:

The auxiliary injection relay (No. 46 in the wiring diagram, placed in the front relay box, left side; CHECK,

however, the identification of the relay with the colour of the cables) is energised for 5 seconds and the

coil Brown/Green cable is closed to ground for 2 ms per second. Disconnect the 4-way connector of

the fuel pump to be able to hear the relay and injector activation. The continuity of the wiring is necessary

for correct activation: no error indications are displayed in case of lack of activation.

Rear Side Coil:

The auxiliary injection relay (No. 46 in the wiring diagram, placed in the front relay box, left side; CHECK,

however, the identification of the relay with the colour of the cables) is energised for 5 seconds and the

coil Brown/White cable is closed to ground for 2 ms per second. Disconnect the 4-way connector of the

fuel pump to be able to hear the relay and injector activation. The continuity of the wiring is necessary

for correct activation: no error indications are displayed in case of lack of activation.

DIAGNOSTICS INSTRUMENT: LOGIC ERRORS

Front cylinder central coil P0351

Electrical system

Caponord 1200 - Caponord 1200 Rally

ELE SYS - 206

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands