manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 386

•

Remove the fixed bushing (1), the

movable bushing (2), the ring (3) and

the oil seal (4) from the stem.

•

remove the ring and the dust guard.

THE FOLLOWING PROCEDURE APPLIES TO

THE ADD VERSION.

•

Lock the pumping member in a vice

using the special tool.

•

Lubricate the sliding edges with fork oil

or sealing grease.

•

Using the special key, unscrew the cap

and remove the spring.

•

Pay attention to place the key in the

lower seat of the "lock nut".

Specific tooling

020957Y

 

Key for upper fork nut

020958Y

 

Fork cartridge protection

•

Before removing the cap (1) from the pumping member, the electric cable harness must be

released. To do this, loosen the ring nut (2) and remove the sleeve (3) by unscrewing it.

Suspensions

Caponord 1200 - Caponord 1200 Rally

SUSP - 386

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands