manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 236

to ON and the indicator light will go back to flash-

ing). Speed control is deactivated (indicator light

flashing) if:

- the rider accelerates more than 30 kph over the

cruise speed;

- the clutch is engaged;

- one of the brake switches is activated;

- the vehicle speed exits the previously indicated

ranges;

- the Cruise ON/OFF button is pressed briefly.

The system deactivates entirely, the cruise speed

is reset and the indicator light turns off if:

- the Cruise ON/OFF button is pressed and held

in.

- the RUN/STOP switch is set to STOP;

- the key is turned to OFF.

Level in electrical circuit diagram:

Pre-installations and accessories

Location:

•

On the vehicle: on the handlebar - right

hand side.

•

Connector: under the dashboard cov-

er.

Pin out:

Br/Bl - Ground

Gr - Signal

DIAGNOSTICS INSTRUMENT: ELECTRICAL ERRORS

VCU ERRORS

Cruise Control ON/OFF button error short circuit C1401

Error cause

•

Short to ground found between VCU connector PIN F4 and light switch connector PIN 1 (Br/

Bl cable - power).

Electrical system

Caponord 1200 - Caponord 1200 Rally

ELE SYS - 236

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands