manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 183

•

If shorted to positive: excessive voltage has been detected at PIN 13 of the ENGINE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 13 of the ENGINE connector

Troubleshooting

•

short circuit to positive: check the value shown by the parameter of the BLUE front connector

Throttle Grip position Sensor track B: disconnect the connector and read the value indicated

by the diagnostics instrument: if the voltage does not vary, there is a short circuit in the cable

wiring; replace the throttle grip sensor if the voltage drops to zero.

•

if the circuit is open, shorted to negative: check the throttle grip sensor connector and the

Marelli control unit connector. If not OK, restore. If OK, check circuit continuity between the

two cable terminals. If not OK, restore; if OK, check the cable ground insulation (from the

throttle grip sensor connector or the control unit connector): if the cable is not ground insu-

lated, restore the wiring. If it is ground insulated, and with the switch key set to ON, check

that there is power supply for the potentiometer PIN D and that PIN F is connected to ground.

If both are correct, replace the throttle grip sensor; if not, check the continuity of the cable

that is not functioning properly: if there is continuity, replace the control unit; if not, restore

the wiring

DIAGNOSTICS INSTRUMENT: ELECTRICAL ERRORS

White rear connector throttle grip position sensor - track C P0152

•

short circuit to positive / open circuit, short circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 23 of the ENGINE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 23 of the ENGINE connector

Troubleshooting

•

shorted to positive: check the value shown by the parameter of the white rear connector

Throttle Grip Position Sensor - track C: disconnect the connector and read the value indi-

cated by the diagnostics instrument: if the voltage does not vary, there is a short circuit in

the cable wiring; replace the throttle grip sensor if the voltage drops to zero.

•

if the circuit is open, shorted to negative: with open circuit, short it to negative: check the

throttle grip sensor connector and the Marelli control unit connector. If not OK, restore. If

OK, check circuit continuity between the two cable terminals. If not OK, restore; if OK, check

the cable ground insulation (from the throttle grip sensor connector or the control unit con-

nector): if the cable is not ground insulated, restore the wiring. If it is ground insulated, and

with the key set to ON, check that there is power supply for the potentiometer PIN A and

that PIN C is connected to ground. If both are correct, replace the throttle grip sensor; if not,

Caponord 1200 - Caponord 1200 Rally

Electrical system

ELE SYS - 183

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands