manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 191

Location:

•

on the vehicle: on the front cylinder, in-

side the "V"

•

connector: on the sensor.

Electrical characteristics:

•

Resistance at 25°: 2.05 k

Ω

 ± 100 

Ω

•

Resistance at 60°: 575 k

Ω

 ± 15 

Ω

•

Resistance at 90°: 230 k

Ω

 ± 5 

Ω

Pin out:

1. Yellow/Brown: 0-5 V signal

2. Green/Pink: Ground connection

DIAGNOSIS INSTRUMENT: PARAMETERS

Engine temperature:

•

Example value with key ON: 25° C

•

Example value with engine on: 75° C

•

In case of recovery, this value is set by the control unit: if there is a malfunction after engine

start-up, temperature decreases up to approximately 90°.

Engine temperature pre Recovery:

•

Example value with key ON: -40° C

•

Example value with engine on: -40° C

•

Value drawn from the signal read without taking into account any recovery: the value in the

example refers to an open circuit.

Engine temperature at start-up:

•

Example value with key ON: -40° C

•

Example value with engine on: 25° C

•

The temperature value is stored during engine start-up. With key ON, value -40°C is read.

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

DIAGNOSTIC TOOL: ELECTRICAL ERRORS

engine temperature sensor P0115

•

open circuit, shorted to positive / shorted to negative.

Error cause

Caponord 1200 - Caponord 1200 Rally

Electrical system

ELE SYS - 191

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands