manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 313

•

Position the clutch hub.

•

Fit the clutch-side cover.

•

Check that the measurement has not

changed compared with the one car-

ried out upon removal; tighten the

clutch nut afterwards. If the projection

has changed, rotate the crankshaft to

correctly engage the engine oil pump

drive gear on the clutch housing with

the oil pump driven gear.

•

Fit the washer and a new clutch hub

nut.

•

Tighten the clutch hub nut using the

specific tool.

Specific tooling

9100896

 

Clutch bell stopper

•

Tighten the nut and proceed to caulk.

CAUTION

MAKE SURE THE DISC RING IS INSERTED FACING THE
RIGHT DIRECTION; THE RING'S CONE MUST BE FACING
THE ENGINE.

Caponord 1200 - Caponord 1200 Rally

Engine

ENG - 313

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands