manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 117

Check that the relay connectors are correctly fas-

tened and that the ends are pulled out of their

seats once the component is inserted.

Check that the filter box temperature sensor is cor-

rectly connected.

Check that the Rear ABS connector is secured

correctly.

Check that the boot is inserted well and that the

clamp fastens part of it and part of the sheath as

illustrated in the figure.

•

Small plastic clamp 2.5x160 mm

(0.1x160.in).

Caponord 1200 - Caponord 1200 Rally

Electrical system

ELE SYS - 117

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands