manualshive.com logo in svg

APRILIA Caponord 1200 2016, Manual

Share
Download
APRILIA Caponord 1200 2016 Manual Download Page 224

Electrical specifications:

•

Sensor in vertical position: open circuit

(resistance: 62 kOhm)

•

Sensor inverted: closed circuit (con-

tinuity)

Pin out:

1. Voltage 5V

2. Ground connection

3. Signal

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING,
CAREFULLY READ THE GENERAL TROUBLESHOOTING
CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGIN-
NING OF THE CHECK AND CONTROL SECTION IN THE
ELECTRICAL SYSTEM CHAPTER.

DIAGNOSTICS INSTRUMENT: STATUSES

Fall sensor:

 Normal / Tip over

•

Indication on diagnostics instrument always Normal, even when the sensor is inverted: dis-

connect the connector and, with sensor inverted, check if there is continuity between the

PINS 2 and 3 of the sensor: If there is not continuity, replace the sensor; if there is continuity,

check the connector: if not OK, restore the cable harness. If OK, check continuity to ground

of PIN 2 (pink/black cable): if there is no continuity, restore the cable harness; otherwise,

with key set to ON, check if there is 5V voltage at PIN 1 (orange/black cable). If there is not,

check the Marelli control unit connector (PIN 65).

•

Indication on the diagnostics instrument always Tip over: disconnect the connector and, with

sensor upright, check if there is continuity between the PINS 2 and 3 of the sensor: if there

is continuity, replace the sensor; if there is not, it means that, with key set to ON, there is no

5V voltage at PIN 1: restore the cable harness whose orange/black cable will be shorted to

ground.

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

Electrical system

Caponord 1200 - Caponord 1200 Rally

ELE SYS - 224

Summary of Contents for Caponord 1200 2016






























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands