Setup Pages and Descriptions
53
NXD-700i & NXT-CA7 7” Modero Touch Panels
Protected Setup Page
Back:
Saves the changes and returns to the previously active touch panel page.
Wired icon:
The icon to the left of the Connection Status Icon displays that the current
connection to the Master is
Wired
(image of three networked computers).
Connection Status icon:
This visual display of the connection status allows the user to have a current
visual update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master, requiring a username and password.
Device ID:
•
Number:
Opens a keypad that is used to set and display the current device
number.
•
Name:
Opens a keypad that is used to set and display the current device
name.
Options:
Allows selection of various touch panel features:
• The
Function Show
button enables the display of the channel port and
channel code in the top left corner of the button, the level port and level code
in the bottom left corner, and the address port and address code in the
bottom right corner.
• Use the
Page Tracking
button to toggle page tracking. When enabled, the
touch panel sends page data back to the NetLinx Master, or vice versa
depending on the touch panel settings.
• Use the
Telnet
button to enable or disable the telnet server on the panel. This
feature focuses on direct telnet communication to the panel.
• Use the
Front Button Setup Access
button to activate the grey
Front Setup
Access
button (located below the LCD) to access the firmware pages.
- Default condition is On.
- Press and hold this grey button for
3 seconds
to access the
Setup
page.
- Press and hold this grey button for
6 seconds
to access the
Calibration
page.
• Use the
Security
button to display one of three security settings:
Standard
,
Secure
, and
DoD
. Pressing this button opens a popup window allowing
changes to the Security Profile.
Note
: Refer to the
Security Settings
section on page 54 for very important
information on using this feature.
System Recovery:
Either resets the touch panel to factory default settings and/or wipes out all
existing touch panel pages:
• The
Reset System Settings
button allows a user to wipe out all current
configuration parameters on the touch panel (such as IP Addresses, Device
Number assignments, Passwords, and other presets).
- Pressing this button launches a Confirmation dialog (FIG. 53) which asks
you to confirm your selection.
- This dialog is configured with a delay timer that does not enable the YES
button for 5 seconds. This delay provides an additional amount of time for
the user to confirm their decision.
• The
Remove User Pages
button allows the removal of all current TPD4
touch panel pages currently on the panel (
including the pre-installed AMX
Demo pages
).
- Pressing this button launches a Confirmation dialog (FIG. 53) which asks
to confirm your selection.
- This dialog is configured with a delay timer that does not enable the YES
button for 5 seconds. This delay provides an additional amount of time for
the user to confirm their decision.
Reboot/Shutdown Panel:
Reboot:
Pressing this button causes the panel to restart after saving any
changes.
Shutdown:
Pressing this button causes the panel to shut down after saving
any changes.
Summary of Contents for NXD-700i
