Modero 7" Touch Panels
5
NXD-700i & NXT-CA7 7” Modero Touch Panels
NXT-CA7 Specifications
NXT-CA7 Specifications
Dimensions (HWD):
• Fully raised: 6.86" x 7.96" x 6.93" (17.40 cm x 20.20 cm x 17.60 cm)
• Fully lowered height: 3.70" (9.40 cm)
Power Requirements:
• PoE Powered - No local power supply needed
• Max power draw: 5.5W
Memory:
• 128 MB SDRAM
• 256 MB Integrated flash memory (Not upgradable - factory programmed)
Weight:
2.5lb (1.12kg)
Panel LCD Parameters:
• Aspect ratio: 16 x 9
• Brightness (luminance): 300 cd/m2
• Contrast ratio: 400:1
• Display colors: 256 thousand colors (18-bit color depth)
• Dot/pixel pitch: 0.19 mm
• Panel type: TFT Color Active-Matrix
• Screen Resolution: 800 x 480 pixels (HV) @ 60 Hz frame frequency
Active Screen Area:
6.00” x 3.60” (15.24cm x 9.14cm)
Viewing Angle:
Up/Down/Left/Right: 70/60/70/70
IR Reception Angle:
• Horizontal: + 50° (left and right from center)
• Vertical: + 30° (up and down from center)
Supported Audio Sample Rates: 48000Hz, 44100Hz, 32000Hz, 24000Hz, 22050Hz, 16000Hz, 12000Hz,
11025Hz, and 8000Hz.
Front Panel:
• Light Sensor: Photosensitive light detector for automatic adjustment of the
panel brightness
• Motion Sensor (PIR): Passive Infrared Detector to wake the panel when
panel is approached
• Front Bezel Button: Provides both access to the Setup and Calibration
pages and toggles the panel between a “sleep” or “wake” state. This
button is also user-programmable.
• Speaker: Output of 4 Ohm, 2 Watts, and 300Hz low cutoff frequency
Rear Connectors
• Ethernet 10/100 Port: RJ-45 port for 10/100 Mbps communication.
The Ethernet port automatically negotiates the connection speed (10 Mbps
or 100 Mbps), and whether to use half duplex or full duplex mode.
Power is supplied through Power Over Ethernet (PoE).
CA7 panels communicate with the NetLinx Master using the ICSP protocol
over Ethernet.
LEDs show communication activity, connections, speeds, and mode
information:
• L/A- link /activity - Yellow LED lights On when Ethernet cables are
connected and terminated correctly and then blinks when receiving
Ethernet data packets.
• SPD-speed - Green LED lights On when the connection is 100 Mbps and
turns off when the speed is 10 Mbps.
• Mini-USB Connector: 5-pin Mini-USB connector used for programming,
firmware update, and touch panel file transfer between the PC and the
target panel.
The connector is also used for providing audio output for external
speakers.
Certifications:
• FCC Part 15 Class B
• CE
• IEC60950
• RoHS
Summary of Contents for NXD-700i
