![background image](http://html1.mh-extra.com/html/amx/modero-nxd-cv17/modero-nxd-cv17_operation-reference-manual_2938955047.webp)
Installation
37
CV17 17" Modero Coor Video Touch Panels
5.
Remove the magnetic faceplate/bezel (
A
in
FIG. 39) from the main NXD unit (
B
in
FIG. 39) by gripping
the faceplate and pulling with gentle outward force.
6.
Follow the procedures outlined within the
Step 1: Removing the existing NXD Outer Housing
section on
page 18 to carefully separate the main LCD panel from the back box housing.
7.
Carefully lay the separated LCD (from the main unit) onto a soft cloth resting on a level surface to
prevent scratching of the LCD.
8.
Insert the back box into the cutout to check for fit. Make any adjustments to the dimension of the cutout to
accommodate the back box.
9.
Cutout the notched beam (FIG. 38) using a height of 13.554" (34.43 cm) and a depth
using the following
guideline
.
This notched beam is located on the side of the NXD unit furthest away from the connectors.
Calculate the distance from the edge of the mounting ridge (FIG. 38) to the rear point (on the box)
where the beam touches the back box.
Our example uses
1 3/8" (inches)
(
on the deepest point of the rear back box
).
Calculate the thickness of the drywall/sheetrock. Our example uses
5/8" (inches)
.
The depth of the notch: 1 3/8"
minus
5/8" =
6/8" (inches)
. This value reflects the cutout depth
necessary for the mounting ridge on the back box to be flush against the surface.
10.
Thread the incoming RJ-45, Ethernet, and any other audio/video wiring (from their terminal locations)
through the cutout opening. Refer to the
Wiring Guidelines for the 17" Panels
section on page 43 for
pinout descriptions.
Leave enough slack in the wiring to accommodate any re-positioning of the panel.
11.
Connect all data and power wiring connectors to their corresponding locations along the side of the (un-
powered) NXD touch panel.
Verify the terminal end of the power cable is not connected to a power supply before plugging in the 2-pin
power connector.
FIG. 39
Wall Mount panel (NXD) installation using expansion clips
B
- Main NXD unit consists of
Install the four
drywall clip
sets (included) into
the LCD panel and back box housing
Four notches are
required if the
unit is installed in
drywall using the
four provided
drywall expansion
A -
Faceplate
(bezel)
clips
Notching of one or more
stud beams may be
required if the unit is not
framed into the wall.
13.554"
(34.43 cm)
Mounting
Tab
these holes
The determining factor in the depth of the cut into the beam is the thickness of the
drywall.
The MOUNTING TAB MUST BE FLUSH
against the drywall and therefore,
the depth of the notch depends on that thickness.
Summary of Contents for modero NXD-CV17
