![background image](http://html1.mh-extra.com/html/amx/epica-dgx-32/epica-dgx-32_instruction-manual_2938448024.webp)
Installation and Setup
18
Epica DGX 32 Instruction Manual
System Setup Options
The following table contains eight options for using DGX SC Optical and DGX DVI Boards in an
Epica DGX 32 Matrix Switcher in conjunction with DGX Fiber modules.
Note: DGX Fiber modules can also be used in a standalone, end-to-end solution; see the
documentation for the modules.
A typical system setup is illustrated on page 47 and shows an Epica DGX 32 with DGX SC Optical
Boards used in conjunction with a DGX TX and a DGX RX.
The DGX HD-15 TX and the DGX DVI TX modules can be installed interchangeably. The
DGX HD-15 RX and the DGX DVI RX modules are interchangeable as well, providing for an
extremely flexible system. For example, in the same system, a source device can send a DVI signal and
the destination device(s) can receive an RGBHV signal.
Note: In addition to the system setup options listed in the table above, optical signal flow between an
Epica DGX 32 and an Epica DGX 144 is supported. Contact your AMX representative for this and
other system design possibilities.
Rack Installation and System Setup
The Epica DGX 32 Distribution Matrix enclosure can be mounted in a standard EIA 19 in. (48.26 cm)
rack.
Required Items for Rack Installation:
Enclosure
Standard EIA 19 in. (48.26 cm) rack
Screwdriver
Screws that fit your rack for mounting the enclosure
Power
cords (2)
Surge-protector – highly recommended
Optional Items for Rack Installation:
A
PC or laptop computer with a null modem cable for communication with an Epica DGX 32
via the RS-232 serial (Control) port
Installation Recommendations:
Write the serial number (normally located on rear of enclosure) in an easily accessible
location before installing the Epica DGX 32 in a rack.
Use an earth-grounded power cord / system with the Epica DGX 32.
Attach all power cords to a single surge protector and/or an AC line conditioner.
Apply power to the Epica DGX 32 enclosure before applying power to its source
and destination devices.
System Setup Options – AMX AutoPatch Epica DGX 32 Boards with DGX Fiber Modules
DGX Fiber Module
Epica DGX 32 Input Board
Epica DGX 32 Output Board DGX Fiber Module
HD-15 TX
=
SC Optical
=
DVI
=
Not Applicable
DVI TX
=
SC Optical
=
DVI
=
Not Applicable
Not Applicable
DVI
=
SC Optical
=
HD-15 RX
Not Applicable
DVI
=
SC Optical
=
DVI RX
HD-15 TX
=
SC Optical
=
SC Optical
=
HD-15 RX
HD-15 TX
=
SC Optical
=
SC Optical
=
DVI RX
DVI TX
=
SC Optical
=
SC Optical
=
HD-15 RX
DVI TX
=
SC Optical
=
SC Optical
=
DVI RX
Summary of Contents for Epica DGX 32
