![background image](http://html1.mh-extra.com/html/amx/epica-dgx-32/epica-dgx-32_instruction-manual_2938448052.webp)
Epica DGX 32 SC Optical Boards
46
Epica DGX 32 Instruction Manual
Specifications Epica DGX 32 SC Optical Boards
Applies to input board FG1056-500 and output board FG1056-510.
Compatible AMX AutoPatch DGX Fiber modules:
FG1010-200-01 – AVB-TX-DGX-HD15-SC Fiber
FG1010-210-01 – AVB-TX-DGX-DVI-SC Fiber
FG1010-400-01 – AVB-RX-DGX-SC Fiber-HD15
FG1010-410-01 – AVB-RX-DGX-SC Fiber-DVI
Note: Either Transmitter (TX) module can be used in conjunction with either Receiver (RX) module.
* 96 kHz audio is only available when the source video resolution is 800x600 @ 60 Hz (40 MHz pixel clock) or
greater. Otherwise 48 kHz is the maximum.
** 3000 ft. cable requires 50/125
μ
m OM2 class low loss fiber cable.
***480i and 576i are only available when being transmitted from a DGX HD-15 TX as a Y-Pb-Pr signal.
Important: These boards are compatible only with other AMX AutoPatch products that support
the DGX single fiber technology. They are not compatible with third-party optical distribution
amplifiers or multimode to single-mode converters.
AMX reserves the right to modify its products and their specifications without notice.
Epica DGX 32 SC Optical
Specifications
Parameter
Value
Compatible AMX AutoPatch Fiber Products DGX HD-15 TX and RX, DGX DVI TX and RX,
other AMX AutoPatch DGX SC Fiber signal management
products
Signal Types over Fiber
Video, audio, serial data
Video signal must be present to pass audio and serial data
Resolution Support
640x480 @ 60 Hz up to 1920x1200 @ 60 Hz
Interlaced Resolution Support
1080i 60, 59.94, 50 (fields per second)
576i 100, 50 (fields per second)***
480i 60 (fields per second)***
Audio Support
Analog stereo or S/PDIF (S/PDIF up to 96 kHz sample rate*)
Serial Data Support
Unidirectional RS-232, up to 115.2 k baud
Fiber Cable Type
Multimode Simplex (with SC termination)
50/125
μ
m (preferred) or 62.5/125
μ
m
Fiber Cable Length
Up to 3000 ft. (914.4 m) in with 50
μ
m cable**
Up to 3000 ft. (914.4 m) out with 50
μ
m cable**
Up to 1500 ft. (457.2 m) in with 62.5
μ
m cable
Up to 1500 ft. (457.2 m) out with 62.5
μ
m cable
Optical Budget
9.75 dBm (typical) between DGX TX and input board
9.75 dBm (typical) between output board and DGX RX
Optical Modulation Amplitude (OMA) Output: -6.25 dBm (typical)
Optical Modulation Amplitude (OMA) Input Sensitivity: -16.0 dBm
(typical)
Power Output of Laser Radiation (max.)
4.08 mW (DGX 32 SC Optical Output Board)
Safety Certifications
Class 1 Laser Product (Class 3R Laser Product when fiber is
disconnected from the unit) IEC 60825-1, 2001
(DGX 32 SC Optical Output Board)
Fiber Connector
SC optical
Summary of Contents for Epica DGX 32
