manualshive.com logo in svg

Amazone AD 3000 Super Classic Line, Operating Manual

Share
Download
Amazone AD 3000 Super Classic Line Operating Manual Download Page 99

 

 

 

Coupling and uncoupling the implement

 

AD 3000 Super  BAH0107-0  02.20

 

99

 

  8.  Raise the combination so that the parking 

supports are just above the ground. 

  9.  Remove the parking supports (Fig. 95/1). 

 10.  Park the combination without parking 

supports. 

 11.  Apply the tractor parking brake, switch the 

tractor engine off and remove the ignition 
key. 

 

 

Fig. 95 

 

 

DANGER 

Remove the parking supports immediately after coupling the 
seed drill on the soil tillage implement.  

The parking supports do not have a locking device. When transporting 
the combination, they can accidentally wander out of the mounts and 
cause serious accidents.  

 

 12.  Align the pack top seed drill until straight by 

adjusting the top link (Fig. 96/1). Secure the 
top link (lock nut). 

 

 

Fig. 96 

 

 13.  Establish the electric and hydraulic connections between  

 

the soil tillage implement and the seed drill 

 

the tractor and soil tillage implement.  

 

  Instructions for connecting the implement cable can be found in the "Control terminal" operating 

manual. 

 

Summary of Contents for AD 3000 Super Classic Line







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands