Amazone AD 3000 Super Classic Line Operating Manual Download Page 121

Page: 121 / 198

Settings

AD 3000 Super BAH0107-0 02.20

121

Settings

WARNING

Danger of crushing, shearing, cutting, being caught or drawn
in, winding and knocks through:



unintentional lowering of the implement raised using the
tractor's three-point hydraulic system



unintentional lowering of raised, unsecured implement
parts



unintentional start-up and rolling away of the tractor-
implement combination.

Secure the tractor and the implement against unintentional starting
and rolling away before working on the implement.

Wait for the implement to stop, before entering the implement
danger area.

WARNING

Before adjustment, maintenance and repair work
(if not specified otherwise)



couple the implement combination and tractor



lower the implement combination onto level solid ground



apply the tractor parking brake



switch off the control terminal



switch off the tractor engine



remove the ignition spanner



disconnect the power supply between the tractor and the
implement. Disconnect the implement plug .

Risk of accident due to unintentional activation of the metering
unit or other implement components caused by star wheel
movement or radar pulses.

Summary of Contents for AD 3000 Super Classic Line







































































































































































































Search results

Summary of Contents for AD 3000 Super Classic Line

Reviews:

Brands by name

Popular brands

Amazone AD 3000 Super Classic Line, Operating Manual

Search results

Summary of Contents for AD 3000 Super Classic Line

Reviews:

Brands by name

Popular brands