manualshive.com logo in svg

Amazone AD 3000 Super Classic Line, Operating Manual

Share
Download
Amazone AD 3000 Super Classic Line Operating Manual Download Page 116

 

 

 

Coupling and uncoupling the implement 

 

 

116 

 

AD 3000 Super  BAH0107-0  02.20

 

7.2.7 

Uncoupling the seed drill  
from KG/KE/KX 01 soil tillage implements 
with 2-tube system roller frame 

● 

Tooth packer roller PW 600 

● 

Wedge ring roller KW 580

 

● 

Wedge ring roller with matrix tyre profile KWM 600

 

● 

Trapeze ring roller TRW 500

 

● 

Trapeze ring roller TRW 600 

 

DANGER 

Empty the hopper before decoupling the pack top seed drill 
from the soil tillage implement. 

 

 

DANGER 

Danger of being crushed, cut, caught, drawn in or struck 
through insufficient stability and possible tilting of the 
uncoupled implement! 

Set the empty implement down on a horizontal parking area with a 
firm base. 

 

  1.  Move the combination into transport position, see section "Moving the seeding combination into 

transport position", page 159. 

  2.  Park the combination on a level surface with solid ground. 

  3.  Empty the hopper. 

  4.  Apply the tractor parking brake, switch the tractor engine off and remove the ignition key. 

  5.  Disconnect the electric and hydraulic connections between 

 

the soil tillage implement and the seed drill 

 

the tractor and soil tillage implement.  

 

  Instructions for disconnecting the implement cable can be found in the "Control terminal" 

operating manual. 

  6.  Hang the supply lines in the hose cabinet 

(Fig. 131). 

 

 

Fig. 131 

 

Summary of Contents for AD 3000 Super Classic Line







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands