Amazone AD 3000 Super Classic Line Operating Manual Download Page 97

Page: 97 / 198

Coupling and uncoupling the implement

AD 3000 Super BAH0107-0 02.20

7.2.2

Mounting the seed drill
on KG/KE/KX 00 soil tillage implements
with 1-tube system roller frame

●

Tooth packer roller PW 500

●

Wedge ring roller KW 520

on KG/KE/KX 01 soil tillage implements
with 1-tube system roller frame

●

Tooth packer roller PW 500

●

Wedge ring roller KW 520

●

Simplex prismatic roller SX-45 SG (made by Güttler)

●

Simplex prismatic roller SX-45 SU (made by Güttler)

The pack top seed drill is equipped with two link
plates (Fig. 89/1) with socket.

Fig. 89

The 1-tube frame roller
is equipped with 2 bearing brackets (Fig. 90/1).

Fig. 90

Summary of Contents for AD 3000 Super Classic Line







































































































































































































Search results

Summary of Contents for AD 3000 Super Classic Line

Reviews:

Brands by name

Popular brands

Amazone AD 3000 Super Classic Line, Operating Manual

Search results

Summary of Contents for AD 3000 Super Classic Line

Reviews:

Brands by name

Popular brands