manualshive.com logo in svg

Amazone AD 3000 Super Classic Line, Operating Manual

Share
Download
Amazone AD 3000 Super Classic Line Operating Manual Download Page 177

 

 

 

Maintenance and repairs

 

AD 3000 Super  BAH0107-0  02.20

 

177

 

12.3 

Safety 

 

WARNING 

Danger of crushing, shearing, cutting, being caught or drawn 
in, winding and knocks through: 

 

unintentional lowering of the implement raised using the 
tractor's three-point hydraulic system 

 

unintentional lowering of raised, unsecured implement 
parts 

 

unintentional start-up and rolling away of the tractor-
implement combination. 

Secure the tractor and the implement against unintentional starting 
and rolling away before working on the implement. 

Wait for the implement to stop, before entering the implement 
danger area. 

 

 

CAUTION 

Before adjustment, maintenance and repair work  

 

couple the pack top seed drill  
and the soil tillage implement. 

 

lower the implement combination onto level solid ground 

 

apply the tractor parking brake 

 

switch off the control terminal 

 

switch off the tractor engine 

 

remove the ignition spanner 

 

disconnect the power supply between the tractor and the 
implement. Disconnect the implement plug (e.g. ISOBUS plug). 
 
Risk of accident due to unintentional activation of the metering 
unit or other implement components caused by star wheel 
movement or radar pulses.  

 

Summary of Contents for AD 3000 Super Classic Line







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands