Amazone AD 3000 Super Classic Line Operating Manual Download Page 158

Page: 158 / 198

Settings

158

AD 3000 Super BAH0107-0 02.20

8.15

Moving the exact following harrow road safety bar into road
transport/parking position

8.15.1 Moving the road safety bar into road transport position

1. Push the two-part road safety bar (Fig.

202/1) over the tine tips of the exact
following harrow.

2. Fasten the road safety bar with spring

holders (Fig. 202/2) to the exact following
harrow.

Fig. 202

8.15.2 Moving the road safety bar into parking position

Place the road safety bars inside each other and
secure them to the transport bracket (Fig. 203/2)
using the spring holders (Fig. 203/1).

Fig. 203

Summary of Contents for AD 3000 Super Classic Line







































































































































































































Search results

Summary of Contents for AD 3000 Super Classic Line

Reviews:

Brands by name

Popular brands

Amazone AD 3000 Super Classic Line, Operating Manual

Search results

Summary of Contents for AD 3000 Super Classic Line

Reviews:

Brands by name

Popular brands