Amazone AD 3000 Super Classic Line Operating Manual Download Page 194

Page: 194 / 198

Maintenance and repairs

194

AD 3000 Super BAH0107-0 02.20

12.9

Oils and greases

Hydraulic oil



Keep out of the reach of children



May not enter the ground or water



Dispose of properly.

12.9.1 Vario gearbox gear oil

Vario gearbox
Total filling quantity

0.9 litres

Vario gearbox
Gear oil (selectable)

Wintershall Wintal UG22 WTL-HM (ex-works)

Fuchs Renolin MR5 VG22

Fig. 235

12.9.2 Lubricants for grease nipples and grease guns

Lubricate using a lithium-saponified multi-purpose grease with EP additives:

Company

Lubricant designation

ARAL

Aralub HL2

FINA

Marson L2

ESSO

Beacon 2

SHELL

Ratinax A

The lubrication points on the implement are
marked with the symbol (Fig. 236).

Fig. 236

Carefully clean the grease nipple and
grease gun before lubrication so that
no dirt is pressed into the bearings.
Press the dirty grease completely
into the bearings and replace it with
new grease.

Summary of Contents for AD 3000 Super Classic Line







































































































































































































Search results

Summary of Contents for AD 3000 Super Classic Line

Reviews:

Brands by name

Popular brands

Amazone AD 3000 Super Classic Line, Operating Manual

Search results

Summary of Contents for AD 3000 Super Classic Line

Reviews:

Brands by name

Popular brands