Amazone AD 3000 Super Classic Line Operating Manual Download Page 107

Page: 107 / 198

Coupling and uncoupling the implement

AD 3000 Super BAH0107-0 02.20

107

17. Pull out the top carrying arm pin (Fig. 113/1).

Adjust the top link if the carrying arm pin
cannot be loosened.

Fig. 113

18. Put the carrying arm pin (Fig. 114/1) into

parking position and secure with a linch pin.

19. Repeat the procedure for the second

carrying arm.

Fig. 114

The pack top seed drill can move
freely on the parallelogram
suspension after removing the top
carrying arm pins.

20. Establish the electric and hydraulic connections between



the soil tillage implement and the seed drill



the tractor and soil tillage implement.

Instructions for connecting the implement cable can be found in the "Control terminal" operating

manual.

Summary of Contents for AD 3000 Super Classic Line







































































































































































































Search results

Summary of Contents for AD 3000 Super Classic Line

Reviews:

Brands by name

Popular brands

Amazone AD 3000 Super Classic Line, Operating Manual

Search results

Summary of Contents for AD 3000 Super Classic Line

Reviews:

Brands by name

Popular brands