Amazone AD 3000 Super Classic Line Operating Manual Download Page 170

Page: 170 / 198

Use of the implement

170

AD 3000 Super BAH0107-0 02.20

10.5

Emptying the seed hopper and seed housing

CAUTION

Before working on the implement



couple the pack top seed drill
and the soil tillage implement.



lower the implement combination onto level solid ground



apply the tractor parking brake



switch off the control terminal



switch off the tractor engine



remove the ignition spanner



disconnect the power supply between the tractor and the
implement. Disconnect the implement plug.

Risk of accident due to unintentional activation of the metering
units or other implement components caused by star wheel
movement.

DANGER

Dressing dust is toxic and must not be inhaled or come into
contact with the body.

Dressing dust can escape



when filling the implement



when emptying the implement



when cleaning and removing dressing dust

Wear protective clothing, face mask, protective goggles, and gloves.

Summary of Contents for AD 3000 Super Classic Line







































































































































































































Search results

Summary of Contents for AD 3000 Super Classic Line

Reviews:

Brands by name

Popular brands

Amazone AD 3000 Super Classic Line, Operating Manual

Search results

Summary of Contents for AD 3000 Super Classic Line

Reviews:

Brands by name

Popular brands