manualshive.com logo in svg

Amazone AD 3000 Super Classic Line, Operating Manual

Share
Download
Amazone AD 3000 Super Classic Line Operating Manual Download Page 111

 

 

 

Coupling and uncoupling the implement

 

AD 3000 Super  BAH0107-0  02.20

 

111

 

 14.  Remove the top link (Fig. 120/1). 

 15.  Direct persons away from the danger area 

between the soil tillage implement and the 
pack top seed drill. 

 16.  Lower the soil tillage implement and 

carefully pull it forwards without touching 
the pack top seed drill. 

 

 

Fig. 120 

 

 

The supply lines may not get caught 
when pulling the soil tillage implement 
forward. 

 

 

Fig. 121 

 

Danger 

While pulling the tractor forwards, no 
one is permitted to stand between the 
tractor and the implement. 

It is forbidden to climb onto the 
loading board when the implement is 
standing on the parking supports (risk 
of tipping). 

 

 

 

Summary of Contents for AD 3000 Super Classic Line







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands