manualshive.com logo in svg

Amazone AD 3000 Super Classic Line, Operating Manual

Share
Download
Amazone AD 3000 Super Classic Line Operating Manual Download Page 6

 

 

 

 

 

 

6 

 

AD 3000 Super  BAH0107-0  02.20

 

5.6

 

Seeding shaft drive................................................................................................................ 56

 

5.7

 

Metering ................................................................................................................................ 57

 

5.7.1

 

Setting values ........................................................................................................................ 58

 

5.7.2

 

Normal and fine seed metering wheel................................................................................... 60

 

5.7.3

 

Fine seed metering wheel brushes ....................................................................................... 60

 

5.7.4

 

Bean seed metering wheel .................................................................................................... 60

 

5.7.5

 

Bottom flaps .......................................................................................................................... 61

 

5.7.6

 

Slide gate .............................................................................................................................. 62

 

5.7.7

 

Agitator shaft support ............................................................................................................ 62

 

5.7.8

 

Seed rate calibration ............................................................................................................. 63

 

5.8

 

RoTeC Control coulter .......................................................................................................... 66

 

5.9

 

Coulter pressure and seed placement depth ........................................................................ 68

 

5.9.1

 

Coulter pressure adjustment, manually actuated .................................................................. 68

 

5.9.2

 

Coulter pressure adjustment, hydraulically actuated ............................................................ 69

 

5.10

 

Exact following harrow .......................................................................................................... 70

 

5.10.1

 

Exact following harrow tine position ...................................................................................... 71

 

5.10.2

 

Exact following harrow pressure ........................................................................................... 72

 

5.11

 

Roller harrow with contour guidance ..................................................................................... 73

 

5.12

 

Tramlines ............................................................................................................................... 74

 

5.12.1

 

Tramline control, tabular determination................................................................................. 75

 

5.12.2

 

Tramline control, graphic determination ................................................................................ 76

 

5.12.3

 

Functional description ........................................................................................................... 78

 

5.12.3.1

 

Lay shaft coupling, electrically actuated ............................................................................... 79

 

5.12.4

 

One-sided switching .............................................................................................................. 80

 

5.12.5

 

Tramline control 2 and 21 ..................................................................................................... 81

 

5.13

 

Tramline marker .................................................................................................................... 81

 

5.14

 

Track marker ......................................................................................................................... 82

 

6

 

Initial operation .......................................................................................... 83

 

6.1

 

Checking the suitability of the tractor .................................................................................... 84

 

6.1.1

 

Calculating the actual values for the total tractor weight, tractor axle loads and tyre 
load-bearing capacity, as well as the required minimum ballast weight ............................... 85

 

6.1.1.1

 

Data required for the calculation (attached implement) ........................................................ 86

 

6.1.1.2

 

Calculation of the required minimum ballast weight at the front G

V min

 of the tractor 

to ensure steering capability ................................................................................................. 87

 

6.1.1.3

 

Calculation of the actual front axle load of the tractor T

V tat

 ................................................... 87

 

6.1.1.4

 

Calculation of the actual total weight of the combined tractor and implement ...................... 87

 

6.1.1.5

 

Calculation of the actual rear axle load of the tractor T

H tat

 ................................................... 87

 

6.1.1.6

 

Load-bearing capacity of the tractor tyres ............................................................................. 87

 

6.1.1.7

 

Table ..................................................................................................................................... 88

 

6.2

 

Secure the tractor / implement against unintentional starting and  rolling away ................... 89

 

7

 

Coupling and uncoupling the implement ................................................ 90

 

7.1

 

Hydraulic hose lines .............................................................................................................. 92

 

7.1.1

 

Coupling the hydraulic hose lines ......................................................................................... 92

 

7.1.2

 

Disconnecting the hydraulic hose lines ................................................................................. 93

 

7.2

 

Safety instructions for coupling the seed drill ........................................................................ 94

 

7.2.1

 

Coupling and uncoupling the implement combinations - Overview ...................................... 96

 

7.2.2

 

Mounting the seed drill  on KG/KE/KX 00 soil tillage implements with 1-tube system 
roller frame ● Tooth packer roller PW 500 ● Wedge ring roller KW 520 on 
KG/KE/KX 01 soil tillage implements with 1-tube system roller frame ● Tooth 
packer roller PW 500 ● Wedge ring roller KW 520 ● Simplex prismatic roller SX-45 
SG (made by Güttler) ● Simplex prismatic roller SX-45 SU (made by Güttler) .................... 97

 

7.2.3

 

Uncoupling the seed drill  from KG/KE/KX 00 soil tillage implements with 1-tube 
system roller frame ● Tooth packer roller PW 500 ● Wedge ring roller KW 520 from 
KG/KE/KX 01 soil tillage implements with 1-tube system roller frame ● Tooth 
packer roller PW 500 ● Wedge ring roller KW 520 ● Simplex prismatic roller SX-45 
SG (made by Güttler) ● Simplex prismatic roller SX-45 SU (made by Güttler) .................. 100

 

7.2.4

 

Mounting the seed drill on KG/KE/KX 00 soil tillage implements with 2-tube system 
roller frames ● Tooth packer roller PW 600  ● Wedge ring roller KW 580 ......................... 103

 

Summary of Contents for AD 3000 Super Classic Line







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands