manualshive.com logo in svg

Amazone AD 3000 Super Classic Line, Operating Manual

Share
Download
Amazone AD 3000 Super Classic Line Operating Manual Download Page 122

 

 

 

Settings 

 

 

122 

 

AD 3000 Super  BAH0107-0  02.20

 

8.1 

Folding the steps up and down 

 

 

DANGER 

Never climb onto the steps and the loading board when the seed 
drill is parked on the supports (risk of tipping). 

Climbing up is only permitted when the seed drill is coupled to the soil 
tillage implement. 

 

 

CAUTION 

Only step onto the loading board via the steps. 

Climbing onto the loading board without using the steps can lead to 
serious injuries due to falling. 

 

 

Always fold up the steps before starting operation or road transport. 

 

 

DANGER 

A latch (Fig. 140) represents the 
mechanical transport locking 
mechanism for the steps. 

The arrow shows the pulling direction 
for unlocking. 

Check the latch for proper seating 
after folding in the steps. 

 

 

Fig. 140 

 

 

Summary of Contents for AD 3000 Super Classic Line







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands